View metadata
Technical Data
Lady Effects Pearl
Product description
Lady Effects Pearl is a high quality, water borne product and is ideal to create a shimmering wall finish. Lady Effects Pearl produces a finish that is lustrous as well as tranquil thereby offering numerous colourful solutions for interior decoration.
Recommended use
Lady Effects Pearl is specially formulated for interior use on cement plaster, concrete, gypsum board, MDF, plywood etc. It is highly recommended for prestigious interiors such as Hotels, Restaurants, Luxury villas, Palaces, Mosques, Museums and Art Galleries, Foyers and Lobbies etc.
Comments
Theoretical spreading rate obtained is 8 - 10 sq. m/lit/coat.
* Spreading rate will vary depending on the film thickness applied and the type of finish.
Physical properties
Colour
As per the colour card
Solids (vol %)*
34
±
2
Gloss
Semigloss
*Theoretically calculated
VOC - 74 gms/lit (theoretical) when measured as per ISO EU for the base.
Surface preparation
The surface must be sound, clean, dry and completely free from dust, oil, laitance etc. All traces of release agents must be removed. On chalky and dusty surfaces, all loose material must be removed by stiff bristle brushing. Fill any imperfections with Jotun Stucco Putty after application of Jotun PVA Primer. Apply two coats of Fenomastic Emulsion Matt (40% diluted) tinted with the recommended colour followed by the topcoat.
Other surfaces
The coating may be used on other substrates. Please contact your local Jotun office for more information.
Condition during application
The temperature of the substrate should be minimum 10°C and at least 3°C above the dew point of the air, temperature and relative humidity measured in the vicinity of the substrate. The coating should not be exposed to oil, chemicals or mechanical stress until fully cured.
Application methods
Other
Trowel, pallet knife or other suitable dispenser.
Application data
Mixing ratio (volume)
Single pack.
Thinner/Cleaner
Water
/
/Lady Effects Metallic thinner
Note
Apply Lady Effects Pearl onto small areas by using a spatula, smooth the material to obtain a truly level surface. It is highly recommended that Lady Effects Pearl be applied by a skilled and professional painter.
Drying time
Drying times are generally related to air circulation, temperature, film thickness and number of coats, and will be affected correspondingly. The figures given in the table are typical with:
* Good ventilation (Outdoor exposure or free circulation of air)
* Typical film thickness
* One coat on top of inert substrate
* Relative humidity 70%
Substrate temperature
10°C
23°C
40°C
Surface dry
12
h
3
h
1
h
Through dry
24
h
5
h
3
h
Dry to recoat, minimum
1
24
h
5
h
3
h
Dry to recoat, maximum
2, 3
1. Recommended data given for recoating with the same generic type of paint.
2. In case of multi-coat application, drying times will be influenced by the number and sequence and by the total thickness of previous coats applied – reference is made to the corresponding system data sheet.
3. The surface should be dry and free from any contamination prior to application of the subsequent coat.
The given data must be considered as guidelines only. The actual drying time/times before recoating may be shorter or longer, depending on film thickness, ventilation, humidity, underlying paint system, requirement for early handling and mechanical strength etc. A complete system can be described on a system sheet, where all parameters and special conditions could be included.
Typical paint system
On Primed surface apply two coats of Stucco followed by 2 coats of Fenomastic Emulsion Matt (40% diluted) tinted with the recommended colour and then followed by 1 - 2 coats of
Lady Effects Pearl
.
Refer to Surface Preparation and Application Method.
Other systems may be specified, depending on area of use
Storage
The product must be stored in accordance with national regulations. Storage conditions are to keep the containers in a dry, cool, well ventilated space and away from source of heat and ignition. Containers must be kept tightly closed.
Handling
Handle with care. Stir well before use.
Packing size
0.9 lit in a 1 liter can and 3.6 lit in a 4 liter can.
Packing may vary from country to country according to local requirements.
Health and safety
Please observe the precautionary notices displayed on the container. Use under well ventilated conditions. Do not breathe or inhale mist. Avoid skin contact. Spillage on the skin should immediately be removed with suitable cleanser, soap and water. Eyes should be well flushed with water and medical attention sought immediately.
For detailed information on the health and safety hazards and precautions for use of this product, we refer to the Material Safety Data Sheet.
DISCLAIMER
The information in this data sheet is given to the best of our knowledge based on laboratory testing and practical experience. However, as the product can be used under conditions beyond our control, we can only guarantee the quality of the product itself. We also reserve the right to change the given data without notice. Minor product variations may be implemented in order to comply with local requirements.
If there is any inconsistency in the text the English (UK) version will prevail.
Jotun is a World Wide company with factories, sales offices and stocks in more than 50 countries. For your nearest local Jotun address please contact the nearest regional office or visit our website at www.jotun.com
ISSUED
26 NOVEMBER 2010
BY JOTUN
THIS DATA SHEET SUPERSEDES THOSE PREVIOUSLY ISSUED
PDF Version :
- TDS - Lady Effects Pearl - English (uk) - Issued.26.11.2010.pdf
Additional PDF versions: